Difference between revisions of "IODD-2541"

Revision as of 12:13, 25 May 2016

외형

Functions

Bootable Virtual CD-ROM, DVD-ROM, Blu-ray Drive
- There is no need to buy DVD-ROM and blank media for OS installation.
- ISO (CD, DVD, Blu-ray) is supported.
Bootable Virtual USB Drive and Flash Drive.
- iODD supports OS installation and Multi Booting. (and "Windows-To-Go")
- Virtual Disk Drive - can do all functions as USB Flash Drive can do
- VHD and VMDK (Virtual Disk Drive), RMD (Virtual Flash Drive), IMA (Virtual Floppy Disk Drive) are supported.
Multi LUN
- max 1 optical drive, 1 hard drive, 4 virtual drives are supported at the same time.
hotkey for safely removal.
- The last physical safeguard. this key provides the safe removal.
Write Protection
- The last logical safeguard. I keep my drive. Good bye Virus.
- Optional Write Blocker. (Hard wired)
Real-time AES 256-bit XTS Military Grade Encryption ( iODD-2541 )
- 4-15 Pin digits. 6 digits is enough for protecting your data. (against the developer of iODD-2541)
- All functions work well with Encryption
- Encryption is optional. you can use without encryption.
Maintain Loading State
- Save and maintain the loading state and menu for next boot.

메뉴

Mode Select - Define USB devices mode
1. Dual Mode - 1 Hard Disk Drive and 1 Optical Disk Drive
2. HDD Mode - 1 Hard Disk Drive.
3. ODD Mode - 1 Optical Disk Drive.
USB Control
1. Write Protect - Write Protect the internal Disk Drive (Not Virtual Drive)
2. Refresh - Reconnect the iODD
3. Safe Removal - Stop the spindle motor and power down the Disk Drive
4. Umount VHDD - Umount All the Virtual Disk Drives
Information
1. S.M.A.R.T. - Display the following status of the internal Disk Drive
  1. HDD Health - Disk Drive Health
  2. HDD Temp - Disk Drive Temperature
  3. HDD Model - Disk Drive Model
  4. HDD Serial - Disk Drive Serial
2. Product Info
  1. Firmware Ver - iODD's Firmeare Version
  2. USB Speed - Currently connected USB Speed
  3. USB Lowest Volt - USB BUS lowest voltage
  4. Current Voltage - USB BUS current voltage
Setting
1. LCD Bright - Adjust LCD back-light bright
2. Idle Bright - Adjust LCD back-light bright in power down mode
3. Standby time - Adjust the inactive time before power down mode is active
4. Load Default - Restoring all settings to their default values
Encryption
- Warning - The Following action will destroy HDD data permanently
- But, Remove Encryption right after Set Encryption does not destroy HDD data
1. Set Encryption - Input 4 - 15 digit PIN
2. Remove Encryption

Specifications

External Interface - USB 1.1 / 2.0 / 3.0 (MAX 5G bps)
Internal Interface - SATA 1.0 / 2.0 / 3.0 (Backward Compatible)
2.5" HDD, SSD (9.5mm width) can be installed.
3-way jog switch, Back Button, USB 3.0 micro B-Type connector.
LCD - 128 * 32 dots.
Material - Aluminum, PC (Plastic).

How to use

At first please refer to the below Manual.

Basic function

iODD's Sample Folder Tree

create a folder named "_ISO" at root folder.

This folder tree is an example.

Any file name and folder name under "_ISO" is acceptable

J:
├─ _ISO
│  │  Hiren’s BootCD 15.2.iso
│  │  ubuntu-14.04.4-desktop-amd64.iso
│  │  Windows 10.iso
│  │  Windows XP sp3.iso
│  │  (max 32 files or subfolders in a folder)
│  │  
│  ├─IMA for Floppy
│  │      Bios updater.ima
│  │      MS-DOS 6.0.ima
│  │      Symantec Ghost.ima
│  │      
│  ├─RMD for Setup
│  │      Win 7Ent_x86_x64+8.1Pro+10Pro vol2.RMD
│  │      Win7_Ult_SP1_Russian_x64.RMD
│  │      Windows 10.RMD
│  │      
│  └─VHD for Booting
│      │  linuxmint-17.3-cinnamon-32bit.vhd
│      │  Windows 10 Win2Go.vhd
│      │  Windows 7 OS Booting.vhd
│      │  
│      └─Nested Subfolders is allowed
├─Your Folder 01
├─Your Folder 02
├─Your Folder 99
│  Your files 01.txt
│  Your files 02.txt
│  Your files 99.txt

2531 Keys

Browsing
- Jog Dial Up/Down. - list Up/Down.
- Jog Dial push. - Select a file.
- BackUp push. - Go to parent folder.
Menu
- Jog Dial push for 3 seconds. - To enter to Menu mode.
- BackUp push. - To exit.
Long key ( push for 3 seconds )
- Jog Dial lift up. - refresh the file lists
- Jog Dial get down. - Go to Power Saving State
- Jog Dial push. - enter to Menu mode
- BackUp push. - Reboot. and detach all virtual drives (VHD, RMD, IMA)
Startup Keys (during startup)
- Jog-Dial lift up. - Start up with CD-MODE
- Jog-Dial get down. - Start up with HDD-MODE
- Jog Dial push. - reset the loading state. Start up with DUAL-MODE
- BackUp push. - Start up with Write-Protected mode.

2541 Keys

Browsing
- Up/Down list - 2 / 8
- Select a file - 5 (or 6, for maintaining loading state)
Menu
- Menu - to enter to Menu. (or Exit).
- 4 - Go to upper list
Long key ( push for 3 seconds )
- 1 - Go to Power Saving State
- 3 - reboots iODD
- 4 - refreshes file lists
- 7 - Reboot. and detach all virtual drives (VHD, RMD, IMA)
- 0 - Reboot. and temporarily disable Write-Protection
There is not Startup key

Go to Power Saving State

Power Saving State : Spindle motor is stopped and LCD brightness is low.

CD loading state is saved.

Jog Dial. down for 3 seconds. (2531).
1. push for 3 seconds. (2541).

Selecting a file

In order to maintain loading state, you must save the state.

refer to the above key operations.

(2531) #2531 Keys
- If Firmware version is 1558 or higher, loading state is automatically saved.
- If not, you must save it manually. (Go to Power Saving State)
(2541) #2541 Keys
- If Firmware version is lower than 6(7)9-05, button 6 has no function.

Safely Removal In OS

If iODD's partition is NTFS, then this function is mandatory when disconnecting iODD from host.

NTFS does not write Immediately the data to HDD.

Please do Safely Removal before disconnection.
If iODD is in write-protected mode and an error message appears, then disable write-protect option. and retry this function.

Initialization

the firmware is two sorts. (NTFS type, FAT32/exFAT type)
NTFS firmware version is shipped.
If you use FAT32 or exFAT Partition, then run FAT Firmware Updater. (FAT32 exFAT Partition)
follow the next steps

assemble the HDD or SSD with iODD
connect the iODD to PC
initialize the drive to MBR. (wken:MBR)
Format the first partition as NTFS. (if the firmware is FAT, then format it as FAT32 or exFAT)
- In FAT32 partition there is 4G byte file size limitation. please use that carefully.
create "_ISO" folder in root folder. (not case sensitive)
copy ISO file to "_ISO" folder. (or create VHD RMD IMA files)
safely remove iODD. ( very Important if NTFS). (safely remove).
If Power Saving mode is active, then disconnect and reconnect the USB cable.
- If not, then Go to Power Saving State
- If "Plug Out ..." (or "Plug Out ...") message appears, reconnect the USB cable.
The following messages will appear sequentially in LCD
- "iodd 253(4)1"
- a file name

Initialize All

If Initialization fails, follow the next steps

disconnect the USB cable.
remove the HDD from iODD. and Connect directly it to PC.
Initialize it to GPT. (msen:GPT)
redo Initialization (from the first step). (your HDD is initialized as MBR -> GPT -> MBR).
Open back cover
Press tact switch
Connect USB cable
Wait 7 seconds
Release tact switch
Wait 1 minutes
All done

First Aid

If it has failure suddenly, try one of the following steps until the error is clear

(2531). press the Jog Dial and hold. and then connect iODD to PC. (#2531 Keys. refer to Startup Keys)
try Safely Removal In OS.
Check Disk for iODD ( for Windows)
Rename "_ISO" folder name to other name. create new folder named "_ISO". and copy files to this folder. (not moving)
Update it with the latest firmware.
Backup the data of iODD, and Initialize All

If there is hardware problem

Reboot the PC
Please change USB cable
Connect iODD to the port of PC back panel.
Try it on another pc
Please change the HDD.

Using a Virtual USB Optical Drive (DVD-ROM or Blu-ray ROM)

copy ISO files to "_ISO" folder. (or to subfolder)
Safely Remove. (Required for NTFS )
If Power Saving mode is not active , then Go to Power Saving State
- If "Plug Out ..." (or "Plug Out ...") message appears, disconnect the iODD.
Connect iODD to a PC. and power on the PC.
(Optional) select iODD or USB CD-ROM as the first priority of BOOT order in BIOS.
If a file has not been selected, then select an ISO file. Selecting a file
If PC doesn't find boot device, then reboot the PC. (Ctrl-Alt-Del)

Booting Error

Confirm whether the ISO file is bootable.
If your PC does not support multi LUN, please select CD-MODE (or ODD-MODE).
In order to confirm whether the ISO file is able to boot, please try to test it with the validated PC.
Although it is bootable ISO file, please confirm whether the result with a real USB DVD-ROM is the same
If the ISO file can be boot with USB DVD-ROM, then use USB Y-CABLE for adding external power.
If your laptop has own internal DVD-ROM, please disable internal DVD-ROM at BIOS settings. or remove it.
The older OS than motherboard may not have an appropriate driver to boot.
- ex) It is impossible to install a genuine Windows 7 on Skylake platform using USB DVD-ROM device.

Using a Virtual USB fixed disk drive (Virtual Hard Disk)

Fixed-size VHD file only is supported. (dynamic VHD and VHDx files are not supported)
Also fixed VMDK file is supported.
Create VHD files directly to iODD by "VHD Tool++". ("VHD Tool++" can creates a file without fragment)
You can create VMDK by changing file extension. (VHD -> VMDK).
If you select a VHD file, then iODD will be rebooted with CD-MODE. and it will be recognized as a USB disk drive.(Selecting a file).
If you want to change to DUAL-MODE or to change Write Protection option, rename the VHD filename. refer to "VHD Tool++"
Max 4 Virtual Drives are supported at the same time ( Successive selection within 3 seconds)

create a VHD file using a tool. (VHD Tool++).
If successful, safely remove iODD from OS. (#Safely Removal In OS. Very Important to NTFS.)
If Power Saving mode is not active, then Go to Power Saving State
- If "Plug Out ..." (or "Plug Out ...") message appear, disconnect the iODD.
Connect iODD to a PC. and power on the PC.
(Optional) select iODD or USB Device as the first priority of BOOT order in BIOS.
If a file has not been selected, then select a VHD file. (Selecting a file)
If PC doesn't find boot device, then reboot the PC. (Ctrl-Alt-Del)

Using a Virtual USB Removable Flash Drive (Virtual USB Flash Drive)

Almost the same as the above method. (Using a Virtual USB fixed disk drive)
But the file extension must be changed. "VHD" -> "RMD"

Using a Virtual USB Floppy Drive (Virtual FDD)

This method is not supported on some computers.
Uncompressed floppy image IMA, IMG, BIF, VFD are supported.
IMG, BIF, VFD image file extension must be renamed to IMA.
Almost the same as the above method.

Manual

Troubleshooting

=== Error Messages ===ㅋ

If LCD message shows like the followings

Check HDD

Do #First Aid

1st Partition

This error occurs when the Firmware and the First Partition of iODD is not matching.
Please Check the above #Initialize.

bad or N/S HDD

Because iODD does not read the internal HDD.
Please change the HDD or USB cable.

Too Many Files

iODD can list max 32 files or sub folders in current folders.
Please use sub folders to avoid many files in a folder.

NO _ISO Folder

Make a folder named _ISO at root folder.

NO - DISC

Because there in no files or sub folders in _ISO folder.

Disc Locked

Because the OS or a application has locked the ODD drive at any reasons.

DEFRAG

ISO file can have max 24 fragment in physical sector address. VHD and RMD must have no fragment.
To solve this situation, please do Disk Defragmenter for Disk Defragmentation.

vDISK Limit

The max number of Virtual disk drives is 4.
You may select more than 4 Virtual drives.

Already Hit

You may select the file that have been selected yet.

Not Use Dynamic

The VHD file selected is Dynamic VHD file. fixed VHD is only supported.

Not Use Sparse

The sparse image file is not supported as Virtual Drive.

QNA

화면에 IODD 2541만 출력됩니다.

하드웨어 문제인 경우이며 다음중 하나를 실행하세요

하드 디스크를 바꿔서 테스트 해봅니다.
USB포트를 PC의 후면에 꽃습니다.(PC의 전면 전압이 낮은경우)
USB케이블을 교체합니다.(스마트폰에 사용되는 5핀 케이블도 테스트로 사용할 수 있습니다)
PC를 재부팅 합니다.
HDD를 교체합니다. ( HDD에서 소리가 나거나 문제가 있는경우).
만약 USB허브를 사용하고 있다면,허브를 사용하지 말고 PC에 아이오드를 직접 연결합니다.
다른 PC에 연결해 봅니다.
위의 처방에도 이 현상이 지속된다면 A/S 접수 해주세요

가상 드라이브 (VHD, RMD, IMA)를 마운트 하면 자동으로 씨디-모드 로 되고 듀얼-모드 로 변경하면 쓰기 금지가 됩니다.

파일명을 변경하면 됩니다. VHD Tool++ 참조 바랍니다.

가상 드라이브 (VHD, RMD, IMA) 마운트를 해제하고 싶습니다.

다음중 하나를 실행하세요

'7' 버튼을 길게 누른다 ( 펌웨어 6(7)9 이상 부터 )
Menu->Advanced->Umount VHDD

펌웨어 업데이트가 자꾸 실패합니다.

업데이트 방법 을 확인하세요

펌웨어

주의사항

펌웨어는 FAT 버전과 NTFS 버전이 있으며 또한 6x 와 7x 버전이 있다
7x 버전은 6x 버전에 비해 무작위 암호 해킹 방법에 대응이 잘되어 있다.
6x 버전도 충분히 안전하지만 7x 버전은 더욱더 안전하다.
6x 버전과 7x 버전과 호환은 안되므로 펌웨어 변경시에는 반드시 하드 디스크 데이터를 백업 해야 한다.

업데이트 방법

Template:틀:iODD 업데이트 방법

@@ Line 69: / Line 69: @@
 ''Check HDD''
 <div class="mw-collapsible-content">
-:NTFS 인경우 [http://windows.microsoft.com/ko-KR/windows7/Safely-remove-devices-from-your-computer 안전 제거]를 안하고 드라이브를 제거하면 캐시 데이터를 저장하지 못했을때도 발생합니다.:
+Do [[#First Aid]]
-:증상이 해결될 때까지 다음 순서에 따라 하나씩 실행하여 주십시오.
-# OS 상에서 [http://windows.microsoft.com/ko-KR/windows7/Safely-remove-devices-from-your-computer 안전 제거]를 하고 재연결 한다.
-# 윈도우즈에서 [[msko:디스크 오류 검사|디스크 오류 검사]]를 진행하세요.
-# 하드 디스크를 바꿔서 PC와 연결합니다.
-# 새로운 _ISO폴더를 생성하고 자료를 하나씩 복사해서 증상을 확인합니다.(기존의 _ISO폴더는 이름을 바꾸세요, 이동이 아니라 복사입니다)
-# 동일한 증상이 반복된다면 데이터를 백업한 후 HDD를 포맷하여 주세요.
-# 최신 펌웨어로 업데이트 해 주세요.
-:Try one of the following steps in order, until the error is cleared.
-# It can be occurred When disconnecting iODD without [http://windows.microsoft.com/ko-KR/windows7/Safely-remove-devices-from-your-computer Sefely Removal]
-#* If Write-protected is on, Change to off.
-#*
-# Check Disk for iODD ([[msen:check%20disk|for Windows]])
-# Rename ''_ISO'' folder to ''old_ISO''. Create new ''_ISO'' folder, and copy files to this folder (not move)
-# Backup the data of iODD, and Initialize iODD with GPT and successively Initialize iODD with MBR. Format the iODD.
-# Update the firmware with latest.
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''파티션 에러''
+''1st Partition''
 <div class="mw-collapsible-content">
-:펌웨어 종류와 iODD 드라이브의 첫번째 파티션과 맞지 않아서 일어나는 메시지 입니다.
+* This error occurs when the Firmware and the First Partition of iODD is not matching.
-:위의 [[#처음 세팅|처음 세팅]] 을 확인하세요
+* Please Check the above [[#Initialize]].
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''하드 디스크 이상''
+''bad or N/S HDD''
 <div class="mw-collapsible-content">
-하드 디스크를 읽지 못하는 경우 입니다.
+* Because iODD does not read the internal HDD.
-증상이 반복되면 다른 하드 디스크로 교환하세요
+* Please change the HDD or USB cable.
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''파일수 한도 초과''
+''Too Many Files''
 <div class="mw-collapsible-content">
-루트 디렉토리나 _ISO폴더안에 32개 이상의 파일/폴더가 있을때 발생하는 메시지 입니다.
+* iODD can list max 32 files or sub folders in current folders.
-서브 폴더를 사용해서 자료를 정리하세요
+* Please use sub folders to avoid many files in a folder.
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''_ISO 폴더 없음''
+''NO _ISO Folder''
 <div class="mw-collapsible-content">
-iODD 드라이브의 첫번째 파티션의 루트 폴더에 ''_ISO'' 폴더를 만드세요
+* Make a folder named ''_ISO'' at root folder.
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''지원 파일 없음''
+''NO - DISC''
 <div class="mw-collapsible-content">
-''_ISO'' 폴더 에 서브폴더나 이미지 파일이 없는 경우 입니다.
+* Because there in no files or sub folders in ''_ISO'' folder.
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''디스크 잠김''
+''Disc Locked''
 <div class="mw-collapsible-content">
-OS 나 프로그램이 실행하면서 광드라이브를 어떤이유로 락킹 시킨상태 입니다.
+* Because the OS or a application has locked the ODD drive at any reasons.
-디스크가 수동으로 빠지지 않게 되는데, 해결책은 iODD 를 재연결 하면 됩니다.
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''조각모으기 필요''
+''DEFRAG''
 <div class="mw-collapsible-content">
-ISO 파일은 24의 디스크 조각까지 허용되며, VHD 나 RMD 는 조각을 허용하지 않습니다.
+* ISO file can have max 24 fragment in physical sector address. VHD and RMD must have no fragment.
-그 이상이 될경우에는 [[wkko:단편화 제거| 디스크 단편화 제거]]를 위해 [[wkko:디스크_조각_모음_(윈도우)|디스크 조각 모음]]을 실행해 주세요.
+* To solve this situation, please do [[wken:Disk_Defragmenter_(Windows)|Disk Defragmenter]] for [[wken:Defragmentation| Disk Defragmentation]].
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''가상하드 초과''
+''vDISK Limit''
 <div class="mw-collapsible-content">
-최대 4개의 가상 드라이브를 지원하는데, 그 이상 선택했습니다.
+* The max number of Virtual disk drives is 4.
+* You may select more than 4 Virtual drives.
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''이미 선택됨''
+''Already Hit''
 <div class="mw-collapsible-content">
-이미 선택된 가상 드라이브를 다시 선택했습니다.
+* You may select the file that have been selected yet.
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''고정 크기만 지원''
+''Not Use  Dynamic''
 <div class="mw-collapsible-content">
-선택한 VHD는 가변식 입니다. 고정식만 지원합니다.
+* The VHD file selected is Dynamic VHD file. fixed VHD is only supported.
 </div> </div>
 <div class="toccolours mw-collapsible mw-collapsed" style="max-width:800px" >
-''스파스 지원 안함''
+''Not Use  Sparse''
 <div class="mw-collapsible-content">
-가상 드라이브 이미지는 sparse 파일을 지원 하지 않습니다.
+* The sparse image file is not supported as Virtual Drive.
 </div> </div>